ASTM A814 Cold-Worked Welded Austenitic Stainless Steel Pipe

ASTM A814 Cold-Worked Welded Austenitic Stainless Steel Pipe

ASTM A814 / A814M - 08
Standard Specification for Cold-Worked Welded Austenitic Stainless Steel Pipe

Abstract
This specification covers two classes of flanged and cold-bending quality cold-worked straight-beam single or double welded austenitic steel pipe intended for high-temperature and general corrosive services. Pipes of Class SW shall be single-welded with no addition of filler metal and Class DW pipes shall be double-welded with no addition of filler metal. The pipes shall be made by machine-welding or an automatic-welding process, welding from one or both sides and producing full penetration welds with no addition of filler metal in the welding operation. Prior to final heat treatment, the weld bead must be cold-worked by methods such as forging, planishing, drawing, swaging or bead rolling so as to obtain a flush condition on the inside and outside of the pipe. All specimens shall be subjected to transverse or longitudinal tension test, flattening test, and hydrostatic test.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope
1.1 This specification covers two classes of flanged and cold-bending quality cold-worked straight-seam single or double welded austenitic steel pipe intended for high-temperature and general corrosive services.
Note 1—When the impact test criterion for a low-temperature service would be 15 ft·lbf [20 J] energy absorption or 15 mils [0.38 mm] lateral expansion, some of the austenitic stainless steel grades covered by this specification are accepted by certain pressure vessel or piping codes without the necessity of making the actual test. For example, Grades 304, 304L, and 347 are accepted by the ASME Pressure Vessel Code, Section VIII Division 1, and by the Chemical Plant and Refinery Piping Code, ANSI B31.3 for service at temperatures as low as −425 °F [−250 °C] without qualification by impact tests. Other AISI stainless steel grades are usually accepted for service temperatures as low as −325 °F [−200 °C] without impact testing. Impact testing may, under certain circumstances, be required. For example, materials with chromium or nickel content outside the AISI ranges, and for material with carbon content exceeding 0.10 %, are required to be impact tested under the rules of ASME Section VIII Division 1 when service temperatures are lower than −50 °F [−45 °C].
1.2 Grades TP304H, TP304N, TP316H, TP316N, TP321H, TP347H, and TP348H are modifications of Grades TP304, TP316, TP321, TP347, and TP348, and are intended for high-temperature service.
1.3 Two classes of pipe are covered as follows:
1.3.1 Class SW—Pipe, single-welded with no addition of filler metal and
1.3.2 Class DW—Pipe, double-welded with no addition of filler metal.
1.4 Optional supplementary requirements are provided for pipe where a greater degree of testing is desired. These supplementary requirements call for additional tests to be made and, when desired, one or more of these may be specified in the order.
1.5 Table 1 lists the dimensions of cold-worked single- or double-welded stainless steel pipe. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification.
1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.

2. Referenced Documents (purchase separately)
ASTM Standards
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A480/A480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
A999/A999M Specification for General Requirements for Alloy and Stainless Steel Pipe
E112 Test Methods for Determining Average Grain Size
E381 Method of Macroetch Testing Steel Bars, Billets, Blooms, and Forgings
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ASME Boiler and Pressure Vessel Code
SectionVIIIDivision1 Pressure Vessels
SAE Standard
SAEJ1086 Practice for Numbering Metals and Alloys (UNS)

3. Steel Grade
ASTM A814 Grade TP304
ASTM A814 Grade TP304H
ASTM A814 Grade TP304L
ASTM A814 Grade TP304N
ASTM A814 Grade TP304LN
ASTM A814 Grade TP309Cb
ASTM A814 Grade TP309S
ASTM A814 Grade TP310Cb
ASTM A814 Grade TP310S
ASTM A814 Grade TP316
ASTM A814 Grade TP316H
ASTM A814 Grade TP316L
ASTM A814 Grade TP316N
ASTM A814 Grade TP316LN
ASTM A814 Grade TP317
ASTM A814 Grade TP317L
ASTM A814 Grade TP321
ASTM A814 Grade TP321H
ASTM A814 Grade TP347
ASTM A814 Grade TP347H
ASTM A814 Grade TP348
ASTM A814 Grade TP348H
ASTM A814 Grade TPXM-10
ASTM A814 Grade TPXM-11
ASTM A814 Grade TPXM-15
ASTM A814 Grade TPXM-19
ASTM A814 Grade TPXM-29

Keywords
Austenitic Stainless Steel - Cold-Worked Steel Pipes - Corrosive Service Applications - High-Temperature Service Applications - High-Temperature Services - Tubular Products - Welded Pipes And Tubes - Welded Steel Pipes

Previous << NONE

Next >> API Spec 5CT N80-Q Casing Pipe

© 2013 Copyright by HEBEI MACRO ENTERPRIS